Відео

gracias. Dave

As shown you can make your own jump rings. or there are lots of sellers on line. ebay etsy etc plus the big jewellery suppliers (if you want silver ones). Just remember the aspect ratio... The inside diameter is 3.5 times the wire thickness. Dave

18g AWG (1mm) so use an inside diameter of 5.5mm this will give a ratio of 5.5 which is perfect. Dave

Here in the UK there is chain of suppliers called "Hobby weld" at various welding suppliers. you buy a cylinder and then just pay for refills (swaps). for the small home studio this is cheaper than paying contracts with big suppliers. There are other companies too that do this. Google your local welding suppliers. They should also be able to fix you up with regulators and flashback arrestors, mine did, all sorted in one shop. Hope this helps. Dave

Thanks for watching. Dave

"Rocks" can mean anything, so a very vague question. Different rocks will have different hardnesses. You can get diamond coated discs and drills which will work on small pieces. I sometimes drill polished stones for pendants. Usually placing the stone in a tub of water and keeping the tip of the drill wet. Hope this helps, Dave

Thanks for watching. Dave

Good observation. Yes this is my 'work' sweater. The issue comes with using acid pickle, the smallest drop, or splash and the fabric slowly rots. It's a strange phenomenon. Even though the sweater is regularly washed, it continues to rot. It happened before with a cotton work shirt. So beware of pickle. Dave.

You are so welcome! Thanks for watching, Dave

With slightly thicker wire, say 1.2mm you don't need to. In my case I have a welder, so will weld all the rings after completion (takes about an hour). This is more for neatness and finish, rather than strength. But I realise not everyone has a welder. It is 'fairly' simple to solder the rings after completion if you wish. Dave

Thanks for watching, Dave

This is actually the 3000 But it's just a model number. I don't believe it refers to anything specific - just a name. Thanks for watching, Dave

Check out "Dremel 3000 full review" in which i show some of the accessories. Thanks for watching, Dave

Sorry to hear that, but hopefully my tips will help people avoid being ripped off in the future. Thanks for watching, Dave

Exactly. as they say, 'if it's too good to be true'.... Thanks for watching, Dave

Dunnok? I'll have to look that up. I just assumed it was a sparrow (or finch). But my knowledge is limited. Thanks for watching, Dave

Glad it was helpful! Thanks for watching, Dave

Thanks for watching, Dave

Anodised aluminium wire looks good and comes in a range of colours, but is obviously very light weight. "Gold filled" wire with silver can give a nice contrast, without too much cost. Copper works well. And sterling silver can be oxidised, to turn it black for that antique look. You can also make jump rings from twisted wire, for added texture. Dave.

ASPECT RATIO, simple as that. Watch the start of the video again. You have to follow the recipe. A byzantine needs to ideally be 3.5 ratio ie the mandrel you use needs to be 3.5 times the diameter of the wire. If your chain looks too loose, then you are using rings with a bigger aspect ratio. Use a smaller mandrel, or use thicker wire. 3.5 is the magic ratio for a byzantine. Dave.

It's all about the aspect ratio. Thicker wire means you need bigger rings, to keep the same ratio. I use 1mm wire with 5mm inside diameter, which gives me a 7mm wide chain. Still easy to solder, just turn the joints to the outside edge and use paste solder or pick soldering, you can easily do 4 or 5 at a time. Plus it's fun ! Thanks for watching, Dave

Your welcome. Dave

You're welcome. Dave

Difficult to say without seeing it, but there should be an 'inner' shaft which will need to attach to the Dremel and which will ultimately turn the chick at the end. Check that. it is properly engaged with the Dremel. If that makes any sense. Dave.

@@CelticDreamsCoUk Thankyou Dave, will try that 🙂

Fine silver does tend to be softer, and in this case I usually only use 1mm wire, so quite thin rings. Perhaps go a little thicker gauge, or consider soldering, or welding. Dave

Welcome!! Dave

Scotchbrite pads (or wheels), radial discs, or tumbling with ceramic chips. Dave

Scotchbrite pads, radial discs, silicone wheels, emery paper. or tumbling with ceramic chips. Dave.

Glad you enjoyed it. Dave

Glad it helped! feel free to buy me Coffee ; ) link in the description. Dave

Thanks for watching! Dave

Glad you liked it! Dave

Glad I could help! Dave

Glad it was helpful! Dave

Thanks for watching, Dave

Thank you, I will. Dave

Yes it does. But obviously with gold you need to be careful to remove as little as possible, start with a clean bench and to keep all your gold dust. Dave

Same tool, many brands. Dave

It's a very popular service. I simply charge a modest fee for labour, per hour, plus return postage at cost.Obviously each job varies, a simple polishing and refurb can be done in an hour. whereas pieces needing extensive repairs and soldering can take all day. Feel free to email if you have a further enquiry. Dave Mail@celticdreams.co.uk

You're welcome. Dave

I'm sure there are many copies around, and certainly a lot of small butane torches on the market. Dave

Спасибо, за прекрасные комментарии. С наилучшими пожеланиями из Англии. Дэйв Dave

Indeed - as many others have noted. Dave

Watch the video, Everything is shown. Dave

I get asked these questions a lot, so perhaps take a look at a blog I wrote explaining jump ring sizes, and how to buy them. Dave pepetools.com/blogs/news/aspect-ratio-the-magic-number-for-making-perfect-jump-rings-and-chains

Great question...The best way to deal with tool marks, is not to put them in to start with. I don't usually get dents from my pliers. Firstly always use smooth jaw pliers, nothing with teeth or grips on them. Secondly it's a good idea to sand and polish the jaws of your pliers to knock of any sharp edges - i do this with two pairs, which are highly polished and smooth. Lastly, it doesn't require a lot of strength to bend thin jump rings like this, so there is no need to grip them with excessive force. My left hand doesn't even really grip the ring, the ring is twisted in the jaws to open it. Go gentle and don't maul about with the metal any more than you need to. This is good tip for silversmithing in general. Thanks, Dave

@@CelticDreamsCoUk cool thanks for the reply👍🏼

Glad it was helpful! Dave

That's the idea my friend. Thats how you get the bargains. good luck. Dave

@@CelticDreamsCoUk thank you sir. You have a good one. Happy hunting as well

Glad you enjoyed it! Dave